|
There are currently no product reviews.
 ;
The product was good and just what I needed, however I had moderate difficulty with the down load because the sight would not recognize my pass word. I was finally given a direct link to the manual and that worked.
 ;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
;
It is an very good and clear scanned service manual.
very recommended.
;
Easy to order the manual. Good quality and fast delivery.
;
The Service Manual for Sansui AU-9500 was very helpfull, in complete and in good printable condition.
Thanks.
Technical Manual
Beta C360
EXPLODED VIEW
Beta C360 Cabinet � Not for Sale 3 15 10 6 1 7 13 13 14 4 16 5 14
11
8 17 2 16
12 9
ITEM NO. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. ITEM NO. DESCRIPTION QTY. 13. Screw (woofer/faceplate) 20 #8 x 1, PAN, PH ZINC LCS " 14. Screw (terminal cup/level adjuster) 7 PB, OPH, ZINC, #6 x .75" 15. Screw (tweeter mounting) 2 MS, PPH, H/L, BLK, 6-19 x .375" 16. Screw (midrange/network) 10 #6 x .75" PAN, PH, PB, BLK ZINC LCS 17. Bump-on Foot w/Adhesive Backing 4 18. Carton-BetaC360BK 1 Carton-BetaC360BE 1 Carton-BetaC360CH 1 19. Pad - Right & Left - Beta C360 2 20. Owner�s Manual 1 21. 5-Year Warranty Card, Infinity 1
DESCRIPTION Woofer Midrange Tweeter Crossover Assembly Level Adjust Foot Assembly Terminal Cup w/Binding Posts Faceplate, Black (for BK) Faceplate, Gray (for BE & CH) Gasket, Faceplate Assy, Grille, Black Cup, Grille (Black for BK) Cup, Grille (Titanium for BE & CH) Flowerpot, Midrange Plastic Screw (faceplate) #8 x 1, PB, HXS, ZINC "
QTY. 2 1 1 1 1 1 1 1 1 1 8 8 1 8
PART NO. 351512-001 351501-001 351572-001 352096-001 351661-001 338567-001 351903-001 351903-002 351944-001 352066-003 333249-001 333249-003 334072-001 903802-016
PART NO. 900101-012 61867 905401-006 908301-012 330104-001 352170-001 352170-002 352170-003 352171-001 352036-001 335841-003
TO SERVICE THE BETA C360 Remove the grille. 1. Remove the (4) rubber grille retainers on the center section of the front faceplate; this can be accomplished by carefully pulling them out of their cavities with long-nosed pliers or similar tool. 2. Remove the (4) Phillips screws that are now exposed and the (8) Hex screws (5/32 or 4mm) surrounding the woofers. 3. Carefully separate the front faceplate, with tweeter attached, from the cabinet. 4. Woofer: Remove the (4) Phillips screws per driver that are now exposed. 5. Midrange: Remove the (4) Phillips screws that are now exposed. Note the crossover network is not integrated with the rear terminal cup, and must be accessed through the left woofer opening.
Infinity Systems, 250 Crossways Park Drive, Woodbury, New York 11797
4/05
Beta C360
|
